GoPro Wi-Fi Remote ARMTE-001 Battery Replacement Guide – YD362937P

GoPro Wi-Fi Remote losing charge or switching off before your recording session is over? Check the charging connection and identify the remote before considering an internal battery repair.

Aging batteries can shorten runtime, but a damaged charging cable, dirty contacts, or internal fault can cause similar symptoms. A remote that stays powered but will not connect to a camera may need pairing troubleshooting rather than a battery replacement.

Replacement Option: STARNOVO 3.7V 350mAh Replacement Battery for GoPro Wi-Fi Remote ARMTE-001 — YD362937P. Confirm the original pack's size, lead arrangement, and electrical connections before installation.

1. Technical Specifications & Compatibility

The STARNOVO product lists these replacement specifications:

  • Application Covered Here: GoPro Wi-Fi Remote ARMTE-001
  • Battery Reference: YD362937P
  • Nominal Voltage: 3.7V
  • Rated Capacity: 350mAh
  • Listed Dimensions: 4.0 × 25.5 × 37.0 mm
  • Protection: The listing specifies an integrated PCM for overcharge, over-discharge, and short-circuit protection.
  • Package Contents: One replacement battery

This is a third-party STARNOVO battery, not an original GoPro product. It powers the remote, not the camera. References to HERO cameras must not be interpreted as compatibility with their camera battery compartments.

Check the remote's actual model label. Do not assume Smart Remote, The Remote, or other GoPro controllers use the same internal battery simply because their names or appearance are similar.

Connection Note: The independent ARMTE-001 repair guide describes three soldered battery connections. Do not assume this is a plug-and-play repair. Compare the actual replacement leads and original connections before proceeding.

2. Check Charging Before Replacing the Battery

GoPro's Wi-Fi Remote manual describes a dedicated charging cable that locks into the charging slot. Check the cable, accessible contacts, and correct seating before deciding the battery has failed.

  • Use the Correct Cable: Follow the remote manual rather than trying to insert a generic cable into the attachment-key slot.
  • Inspect the Connection: Look for visible damage or contamination. Keep contacts dry and do not insert metal tools.
  • Check the Battery Display: The manual states that the LCD shows battery level during power-on or charging.
  • Separate Power from Pairing Faults: A controller that remains powered but cannot operate the camera may have a connection or compatibility issue.

If the battery is swollen, leaking, unusually hot, or pushing the enclosure apart, stop using and charging the remote. Do not flatten the pack or force the cover closed. Seek qualified repair assistance.

3. ARMTE-001 Battery Replacement — Repair Checklist

If you do not have experience with small electronics soldering and lithium battery handling, use a qualified technician. Do not apply heat directly to the battery pouch or improvise wiring changes.

  1. Confirm the Model: Verify ARMTE-001 and review the complete matching repair guide before opening the remote.
  2. Disconnect Power: Switch the remote off and unplug its charging cable. Work on a clean, dry surface.
  3. Access the Rear Cover: Follow the guide's fastener and opening sequence. Support the housing and avoid forcing components.
  4. Protect the Battery and Display: The guide describes an adhered battery and a display ribbon beneath the board. Do not puncture the pouch or strain the ribbon.
  5. Document Every Connection: Photograph the original lead-to-pad positions before disconnection. Do not identify a connection by wire color alone or assume the third wire can be omitted.
  6. Verify the Replacement: Compare voltage, dimensions, wiring, polarity, and connection requirements. Stop if the pack needs compression, a forced fit, or an unexplained wiring conversion.
  7. Have Soldered Work Completed Correctly: A qualified technician should follow the verified wiring arrangement and avoid shorts, solder bridges, and overheating.
  8. Reassemble Carefully: Restore the board, battery position, cable routing, and seal according to the guide. The case should close without pressure on the battery or trapped leads.

Seal Warning: Opening the remote can compromise its water resistance. Reinstalling the gasket does not verify restoration of the original rating. Do not assume the repaired remote is safe for immersion.

4. What to Expect After the Swap

If battery aging caused the fault, a suitable replacement may improve runtime. It cannot repair damaged charging contacts, a faulty board, or an unrelated pairing problem.

  • Charge After Reassembly: Follow the remote's manual and stop if unusual heat, odor, swelling, or unstable operation occurs.
  • Check Power and Controls: Verify the display and buttons respond normally.
  • Test Camera Connection: Pair with a compatible camera using the correct instructions, then test starting and stopping a recording.
  • Check Real Runtime: Observe performance in normal use. The 350mAh rating alone does not guarantee a specific number of operating hours.

Complete a dry, controlled test before relying on the remote during a trip or recording session.

5. Common Mistakes to Avoid

  • Confusing Remote and Camera Batteries: This pack is intended for the listed remote, not a HERO camera.
  • Assuming Every GoPro Remote Is Identical: Check the model label and internal connection details.
  • Expecting a Connector-Only Swap: The documented ARMTE-001 repair involves soldering.
  • Ignoring the Third Lead: Do not bypass or omit connections.
  • Damaging the Pouch or Display Ribbon: Avoid force and metal tools against the cell.
  • Assuming Waterproofing Is Restored: A closed cover is not proof of a verified seal.

6. Choosing Your STARNOVO Replacement Battery

The STARNOVO product lists a 3.7V nominal voltage, 350mAh capacity, and dimensions of 4.0 × 25.5 × 37.0 mm for the ARMTE-001 application. Check the original pack and electrical connections before ordering or installation.

For compatibility help, email sales@starnovo.com with photos of the remote model label, original battery label, and wiring. Repair shops can also contact us about volume supply.

Get the GoPro ARMTE-001 Replacement Battery →
Back to blog